Mitigation blocks, explained
Sometimes price tries to make a new low and can't. It turns early, then breaks the high above. ICT calls the candle at that high a mitigation block. It works like a breaker, without the raid.
- Before: the up candle at the high
- After the break: bullish mitigation block
- Mean threshold (50%)
- The first low, never taken
Lesson 1 · The failed swing
Price fails to go lower, then breaks the high
The pullback stops above the old low. Sellers couldn't push through. When price then breaks the high, the last up candle at that high flips to support.
- 1 · Swing low
- The low that price will fail to reach again.
- 2 · Swing high
- Mark the last up-close candle at this high.
- 3 · Higher low
- The pullback turns above point 1. The swing has failed.
- The break
- Price trades back above point 2. The candle at 2 is now a bullish mitigation block.
KEYLow, high, higher low, break of the high. The candle at the broken high is the block.
Lesson 2 · Bullish and bearish
A broken high leaves support, a broken low leaves resistance
The bearish one is the mirror: high, low, lower high, then price breaks below the low.
Low, high, higher low, break above the high. The last up candle at the high is support.
High, low, lower high, break below the low. The last down candle at the low is resistance.
KEYLike a breaker, the block is tested from the side price broke away to.
Lesson 3 · Mitigation vs breaker
One thing tells them apart: the third swing
Both end with a break of the middle swing. The difference is whether the third swing took the stops beyond the first one.
The third swing runs below the first low and takes its stops. That raid makes it a breaker.
The third swing turns above the first low. No raid. The swing simply failed, and that makes it a mitigation block.
KEYTook the old low: breaker. Fell short of it: mitigation block. Both are read the same way.
Lesson 4 · What happens next
Bodies should hold; wicks get a little room
The block is the candle's whole range, with its 50% as the mean threshold. Each picture is bullish; for bearish, flip them upside down.
Holds in the top half
Price dips in, stays above the middle line and leaves.
Wick pokes past, body holds
A wick slips a tick or two past the bottom, but the candle closes back inside.
Body closes through
A body closes below the block. It no longer counts as support.
KEYA wick a tick or two past is noise. A body closing past the far side ends it.
Lesson 5 · How to spot one
Four checks, in order
Find three swings: low, high, higher low
For a bearish block: high, low, lower high.
Check the third swing fell short
It must turn before reaching the first one. If it went past, you're looking at a breaker.
Wait for the break
Price trades back past the middle swing (the high, for a bullish block).
Mark the last up candle at that high
Its whole range is the block. Mark the 50% too, and extend them right.
Omen Layers finds mitigation blocks for you, on any timeframe, on one chart.
- Turn on an MB row in the sequencer and pick its timeframe, or type 1h mitigation block in TUNE and press Enter.
- The Swing knob sets how many candles each side make a swing high or low.
- A new block is dimmed until price closes clear of it, then outlined. Once price comes back into it, it reads MB ✓.
- It ends when a body closes past its far side. MEAN THR draws the 50% line.
- The ? beside the row opens a short note like this page.
- Low, high, higher low: the third swing fails to reach the first.
- A break above the high turns the last up candle there into support.
- Took the old low instead? Then it's a breaker.
- Wicks may poke a tick or two past; a body closing past the far side ends it.
Charts on this page are illustrations drawn for teaching. They are not real market data and do not show any product's output. ICT concepts are taught by Michael J. Huddleston; this page is an independent explanation.